SAVAGE BARRELS NO LONGER FOR SALESALE
For all 110 variants (112, 116, 10, 11, etc.,).
"Short" Magnums since 2001 and a few "G" series standard
rifles sold in 2004 have "new" thread, others are "standard".
These descriptions are kept as examples of what you can do with even a small lathe and used take offs.
Savage Factory 30-06 Barrel – Used Take Off 1-10”
Markings: Factory Savage 110
Finish: Gun Kote Semi-Matt
Thread Style: Standard Factory (Locknut – 1.75” usable)
Contour: Medium – Sporter Front Sight still attached
Crown: Factory
Length: 22”
Muzzle Diameter: 18/32”
Stock Number: V001 
PRICE: $50 - SOLD!
Refurb Ruger SS Take Off .22/250 1-12" Medium Sporter
Length: 21 1/2"
Contour: Medium Sporter
Muzzle Diameter: 5/8"
Finish: Stainless polish with some wear marks here and there.
Description: Ruger 223 Barrel with pristine bore (must have been carried
more than it was shot) professionally rethreaded (gunsmith was Skaggs
Gunsmithing) and rechambered to 22/250 (for a coyote hunt out west I never
went on. Never got a chance to try it out, although it will probably be hard
on the ears because it is so short.
SOLD!
Refurbished Remington Take-Off .243 Win CM
Markings: Remington Factory Markings
Finish: Matte
Contour: Medium-Sporter
Tread Style: Standard Factory (Locknut – 1-3/4” usable)
Length: 19.2”
Crown: Stepped
Muzzle Diameter: 20/32”
Description: Unused Remington 700 take-off rethreaded for Savage 110. Suitable
for hunting.
Stock Number: R002 
SOLD!
Refurbished Win Model 70 Take-Off .243 Win
Markings: Winchester
Finish: Factory Blue (showing some wear)
Contour: Light Varmint
Thread: Standard Savage Factory
Muzzle Diameter: 20/32 inch.
Length: 21"
Twist: 1-10"
Description: Model 70 barrel with good bore professionally rethreaded
(gunsmith was Skaggs
Gunsmithing) for Savage. 
R27 - PRICE: SOLD!
Refurbished Douglas Light Contour 270 Win CM
Markings: None
Finish: Matte
Contour: Light
Tread Style: Standard Factory (Locknut – 1-5/8” usable)
Length: 20”
Crown: Dish
Muzzle Diameter: 17/32”
Description: Shortened used custom barrel rethreaded for Savage. If you
can take the recoil and muzzle blast should make a handy hunting carbine suitable
for those long shots that sometime come up.
Stock Number: R004
PRICE: SOLD
Refurb Remington Take Off .223 1-12" CM
Description: Light.223 suitable for varminting or plinking. Shoots 55 gr bullets great. Combined with a Savages light synthetic
stock will make a handy rifle to carry or keep in the back of the truck.
For rifles chambered for standard 30/06 cartridges, bolt heads are available
for cartridge conversion.
Stock Number: R005 - SOLD!
Shilen 1-14 223 CM Medium Sporter
Contour - Medium Sporter
Length - 20 1/4"
Finish - Semi Matt (Matt Gun-Kote over a polished surface)
Barrel was 
removed
from Remington 700 - noticeable vise marks (wrong sized bushing was used)
still visible below finish. The threads are still a little short so a shortened
barrel nut is also provided:
Muzzle Diameter - 9/16"
Crown - Rounded Factory
Threads - Standard Savage threaded shank.
Description: This barrel started life as a pre-threaded short chambered
22/250 remington barrel. With its medium sporter contour it
got too hot to touch after only 5 shots. There wasn't enough shank left to
rethread for 223 and still put it on a remington so it was re-threaded for
Savage. Shoots the WalMart 45 grain Winchester value ammo pretty good. Note
that because of the slow twist it will not shoot the real heavy bullets used
for long range matches.
Stock Number R19
Price: $85.00
Refurb Remington 6mm Medium Sporter - 19.25"
Description: Used sporter weight hunting barrel rethreaded
for Savage standard thread. Tried it out as a medium cartridge that will
feed properly out of a long action magazine. Pleased with the result but
prefer a longer barrel for the type of shooting I do. Handles heavy bullets
real well. The 6mm hits allot harder than the 243. - just look at the comparison
of the cases here.
Stock Number: R14
SOLD!
Refurb 30 Remington Take-off 21" Barrel Sporter 1-10"
Contour: Sporter
Muzzle Diameter: 19/32"
Length: 21"
Finish: Factory Matte, noticeable removal marks near threads.
Description: New Remington take-off, rethreaded for Savage that I never got a
chance to shoot.
R-28 - $60
Douglas 6mm Refurb 22" 1-10 CM
Contour: Medium Sporter - no screw holes.
Finish: Semi Matt Epoxy.
Muzzle Diameter: 5/8 inch.
Description: This was a douglas 243 barrel that was shortened at the
chamber end and re-chambered for 6mm Remington. The threads are a little short in that the barrel nut may extend
past the end of the threads slightly. The above 5 shot group was with factory
loads at 100 meters. I have developed some handloads that don't exhibit as much vertical stringing, but groups are
still oval. This is more than good enough for hunting accuracy.
Stock Number R17
Price: SOLD
Email fro availability.
Shilen 1-10 6mm Varmint CM Barrel
Description: Started life as a prethread for Mauser 98.
Never installed, rethreaded for Savage. Good accuracy as shown in
the picture. Heavy barrel suitable for varmint or target work. THe 6mm Rem
is a much better deer round than 243, but this barrel may be a little too
heavy for carting through the woods. For a comparison of 6mm and 243
see here.
Stock Number - R18 SOLD!
Remington Take-Off Re-threaded and Chambered for 7.62X39
Length: 20"
Muzzled Diameter: 9/16"
Finish: Semi-Matt Gun-Kote backed on finish.
Description: Remington take off (new) in .308 rethreaded for Savage,
cut back in the chamber end and re-chambered for 7.62X39 for plinking with
cheap surplus ammo. For an article on how this barrel was made and tested
see here.
Note:
Threads are shorter than standard Savage since the barrel had to be cut
way back for rechambering There is enough threads for the barrel nut although
you may want a shortened barrel nut for appearance purposes.
R20 - $SOLD!
See Savage Kits page for note on 7.62X39 chambering using standard bolt head and "PPC" extractor.
Remington Take-Off Re-threaded and Chambered for 7.62X39
Length: 20.5"
Muzzled Diameter: 5/8"
Finish: Matt finish.
Description: Remington take off (new) in .308 rethreaded for Savage,
cut back in the chamber end and re-chambered for 7.62X39 for plinking with
cheap surplus ammo. For an article on how this barrel was made and tested
see here.
Note:
Threads are shorter than standard Savage since the barrel had to be cut
way back for rechambering. There is enough threads for the barrel nut although
you may want a shortened barrel nut for appearance purposes.
R21 - $100
Email for availability.
Medium Sporter 7MM Magnum - Remington Rethreaded for Savage
Length: 23"
Contour: Medium sporter 21/32"
Finish: Factory blued.
Description: Remington 700 new take-off rethreaded for Savage. Note that
finish just after threads taken off for threading:
R22 - SOLD!
See the Savage Kits Page for boltheads and tools to switch your favorite long action deer rifle to a magnum round suitable for any North American hunting.
Medium Sporter 7MM Magnum - Remington Rethreaded for Savage
Length: 23 1/4"
Contour: Medium Sporter 21/32" muzzle diameter.
Finish: Semi-Matte Gun Kote over original blue.
Description: Remington lightly used 700 barrel rethreaded and re-chambered for 7MM
Rem Mag.
R23 - SOLD
Email for availability.
See the Savage Kits Page
for boltheads and tools to switch your favorite deer rifle to the
premier magnum round for North American hunting.
Medium Sporter .223 1-14" Twist
Length: 23 1/2"
Contour: Sporter- 19/32 muzzle diameter.
Finish: Gun Kote Matte - heavy coating thrown on for rust protection - can
be lightly sanded to final finish.
Description: Remington 222 barrel with some wear in the throat set back
and rechambered for 223 and rethreaded for Savage. Should shoot lighter bullets
well, but I haven't had a chance to try it out
R26 - $60.00
SOLD!
WILDCATTER - Ruger No. 1 Varmint Barrel, 224 bore, 1-14 twist. Setback and rethreaded for Savage.
Length = 22 1/2"
Contour: Varmint
Muzzle Diameter: 25/32"
Finish: Original factory blue, shows some wear. One inch before turned down
to match major thread diameter.
Description: Got this Ruger No.1 2.250 barrel that seemed to have an almost
pristine bore. I had it professionally rethreaded (gunsmith was Skaggs
Gunsmithing) with an eye towards chambering it in 221 Fireball to go up
against some of the Sako 22PPC shooters in my club. Illness and family problems
have interceded to make projects like that seem not important enough for the
time involved.
It is being sold here as a "wildcatter" so that a hobbyist without a lathe can hand chamber the barrel in a desired caliber. Would be suitable for any of the 22 centerfires, although with the slow twist and short Length it would be a waste to chamber it up in something like 220 swift or 22/250AI.
R25 - SOLD